E17z Compact Excavator
Specifications & Options
E17z
Close/Open all PDF version
Operating weight with canopy and bucket (ISO 6016)
1,749 kg
Transport mass (no attachment)
1,632 kg
Additional weight for long dozer blade
9 kg
Ground pressure with rubber tracks
30.1 kPa
(A)
Bucket pivot angle
196 °
(B)
Maximum reach of working equipment
3,971 mm
(C)
Maximum reach at ground level
3,923 mm
(D)
Maximum working equipment radius with boom at maximum height and dipperstick fully retracted
1,560 mm
(E)
Maximum blade height
220 mm
(E*)
Maximum blade height with long blade
300 mm
(F)
Maximum blade depth
204 mm
(F*)
Maximum blade depth with long blade
254 mm
(G)
Maximum height of working equipment with dipperstick retracted
2,406 mm
(H)
Maximum bucket tooth height
3,378 mm
(I)
Maximum dump height
2,369 mm
(J)
Maximum depth of vertical wall which can be excavated
1,810 mm
(K)
Maximum digging depth
2,249 mm
()
(* Dentoes values which long dipperstick installed)
(A)
Blade height
235 mm
(B)
Clearance, upper structure to ground line
419 mm
(C)
Ground line to top of engine cover
1,138 mm
(D)
Length of track on ground
1,114 mm
(E)
Machine centre line to blade
1,045 mm
(F)
Minimum radius in travel position
2,715 mm
(G)
Overall length of track assembly
1,476 mm
(H)
Overall length in travel position
3,450 mm
(I)
Track lug height
25 mm
(J)
Blade width
980 mm
(J*)
Blade width (extensions extended)
1,360 mm
(K)
Height
2,297 mm
(L)
Track width
230 mm
(M)
Machine centre line to working equipment centre line, left-hand rotation
450 mm
(N)
Machine centre line to working equipment centre line, right-hand rotation
638 mm
(O)
Minimum turning radius
1,190 mm
(P)
Swing clearance, rear
690 mm
(Q)
Working width at maximum right-hand rotation
1,532 mm
(R)
Working width at maximum left-hand rotation
1,370 mm
Make / model
Yanmar / 3TNV74-PBC (Stage V)
Fuel
Diesel
Number of cylinders
3
Displacement
993 cm3
Maximum power @ 2400 rpm (ISO 14396)
11 kW
Maximum torque @ 1800 rpm (SAE J1995)
50.2 Nm
Pump type
Dual piston pump with gear pump
Total hydraulic capacity
41.3 L/min
Piston pump capacity
30 L/min
Auxiliary flow
30 L/min
Auxiliary relief
180.0 bar
Digging force, dipperstick (ISO 6015)
9,108 N
Digging force, bucket (ISO 6015)
16,177 N
Drawbar pull
19,302 N
Travel speed, low range
2.7 km/h
Travel speed, high range
4.3 km/h
Boom swing, left
80 °
Boom swing, right
60 °
Slew rate
10.1 RPM
Fuel reservoir
19 L
Hydraulic reservoir
13.9 L
Noise level LpA(EU Directive 2006/42/EC)
81 dB(A)
Noise level LWA(EU Directive 2000/14/EC)
93 dB(A)
Whole body vibration (ISO 2631–1)
0.9 ms-2
Hand-arm vibration (ISO 5349–1)
1.8 ms-2
- 230 mm rubber track
- 980 mm dozer blade with two 190 mm blade extensions
- Battery disconnect switch
- Control console locks
- Counterweight
- Cupholders
- Double acting auxiliary hydraulics
- Engine monitor with auto shutdown
- Foldable and ergonomic travel pedals
- Full fuel warning alarm
- Horn
- Hydraulic and travel control lockout
- Hydraulic joystick controls
- Hydraulically retractable undercarriage from 1360 mm to 980 mm
- Retractable seat belt
- TOPS/ROPS/FOPS canopy (1)
- Two speed travel
- Upper structure four point tie down
- Water separator
- Work light (boom)
- Warranty: 24 months, 2000 hours (whichever occurs first)
(1) Roll Over Protective Structure (ROPS) – Meets requirements of ISO 3471. Tip Over Protective Structure (TOPS) – Meets requirements of ISO 12117. Falling Object Protective Structure (FOPS) - Meets requirements of ISO 3449.
- Demolition package (boom, arm, bucket cylinder covers & HD travel hoses guard)
- Object handling package (Valves, OWD, Lifteye)
- Long dozer blade
- AUX1 direct return to tank
- AUX1 on arm
- Keyless ignition
- Travel motion alarm
- Additional halogen lights
- Beacon
- Special application kit
- L/R mirrors
- Fire extinguisher
- Klac C and MS01 couplers
Certain specification(s) are based on engineering calculations and are not actual measurements. Specification(s) are provided for comparison purposes only and are subject to change without notice. Specification(s) for your individual Bobcat equipment will vary based on normal variations in design, manufacturing, operating conditions, and other factors.